Re: PIC18F4550 - oscillator settings - FlowCode (pcbbc)
This diagram 1 is NOT correct. 1 on there is not the same as 1 here and here, which are correct and both the same thing.I have attached a correct diagram and re-labelled 5.1 and 5.2. And this diagram...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (viki2000)
Thank you very much for all your effort and the rates.Indeed was a mistake above, because I was in hurry to shut off the PC before my bus was coming. Was more due to the rush and not paying attention...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (pcbbc)
viki2000Thank you very much for all your effort and the rates.Indeed was a mistake above, because I was in hurry to shut off the PC before my bus was coming. Was more due to the rush and not paying...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (viki2000)
Since your last post I had no chance to look into the present matter at all, due to other priorities and summer holiday.Now, because it is a while, I am chewing the above data again.I find only one...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (viki2000)
First of all are 2 clocks: one for CPU and one for USB, both clocks sometimes derived from the same external oscillator as in my case.If we decide to use external oscillator (Primary oscillator...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (viki2000)
Now, comes the tricky part with FlowCode.We just bought the last version of FlowCode 6. It has the screen a bit different compared with FlowCode 5, which I previously used. The meanings of parameters...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (Jim Nickerson)
pcbbcI'd suggest you're probably unlikely to find anyone here with experience of FlowCode. Edit: maybe you will, as having googled it I see it is a MC product I didn't know about! Doh! I think Flow...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (tom maier)
According to the Matrix web site, Flowcode is supposed to allow you to avoid all the complexity and get the job done in minutes. Well, the minutes are expired now! (no fault of viki) Here's the setup...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (Jim Nickerson)
Nice to see you back tom ( or maybe I have not been looking at the right posts )I am not a fan of products like "FlowCode" that claim to do everything for you or the so called Rapid Application...
View ArticleClik here to view.
Re: PIC18F4550 - oscillator settings - FlowCode (tom maier)
I never really left,,, I lurk and make jokes to myself now. That's not as much fun as sharing though, because I'm a pretty tough audience. Smile: " /> The web site is so script heavy now that my...
View ArticleClik here to view.
Re: PIC18F4550 - oscillator settings - FlowCode (DarioG)
Hard work usually pays more " />
View ArticleClik here to view.
Re: PIC18F4550 - oscillator settings - FlowCode (tom maier)
What Dario means by that is once you've gone through the grunt work of doing everything for yourself, you are no longer hindered by the "helpful" development package. You are the master of the...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (viki2000)
Thank you for the comments guys.FlowCode is quite a nice package, lots better than the free Great Cow BASIC (http://gcbasic.sourceforge.net/ ), which I knew before. The different prebuilt blocks as for...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (viki2000)
I have tested the settings for 20MHz crystal using PLL for USB, therefore the parameters are:A = 20MHz – the frequency of the external crystal/quartzB = OSC Select = PLL Division PLLDIV2:PLLDIV0 = div...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (viki2000)
Observation: Firefox does not allow me to submit the post all the time, but with IE there is no problem. For my curiosity I have tested also non-PLL with 20MHz external crystal with a simple 1s on/off...
View ArticleClik here to view.
Re: PIC18F4550 - oscillator settings - FlowCode (viki2000)
Tom, and aside thought regrading Great Cow.Actually you cannot compare it with FlowCode. It is nice that is free, last update on 2010, but there is nu really support to it and in FlowCode are so many...
View ArticleClik here to view.
Re: PIC18F4550 - oscillator settings - FlowCode (DarioG)
let me take a look at "la grande vacca" then " />
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (tom maier)
I wasn't suggesting that you use Great Cow, I was commenting on what is "ease of use?". When you try to make something easy to use you hide the complexity of the problem. Obviously Flowcode doesn't do...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (Iván Sánchez)
if you going to work with a external oscillator, put in "1" the frecuency of oscillator with you workand "2" in osc1/osc2.When i work with the internal oscillator, doesnt run. i recommend working with...
View ArticleRe: PIC18F4550 - oscillator settings - FlowCode (HARI@6189)
i am trying to internal rtc configuration for pic16lf19186but it is not working . please any help to me
View Article